MacOS’da ön tanımlı olarak gelen herhangi bir Disk durumunu belirten uygulama göremedim ben. Disk durumlarını sorgulayabilmek için brew ile gereken uygulamanın kurulması gerekmekte
brew install smartmontoolsKurulum tamamlandıktan sonra aşağıdaki komut çalıştırılır.
Sudo smartctl -a /dev/disk0Aşağıdaki gibi bir çıktı verecektir. Disk hakkında tam detaylı bilgiyi bu sayede çok basit bir şekilde alabilirsiniz.
mertcangokgoz@Mertcan-MacBook-Air ~ » sudo smartctl -a /dev/disk0 1 ↵
smartctl 7.0 2018-12-30 r4883 [Darwin 18.2.0 x86_64] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Apple SD/SM/TS...E/F/G SSDs
Device Model: APPLE SSD SM0128G
Serial Number: S2X
LU WWN Device Id: 5 002538 900000000
Firmware Version: BXZ33A0Q
User Capacity: 121,332,826,112 bytes [121 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: Solid State Device
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4c
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Jan 26 09:50:41 2019 +03
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x001a 200 200 000 Old_age Always - 0
5 Reallocated_Sector_Ct 0x0033 100 100 000 Pre-fail Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 2521
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 1705
169 Unknown_Apple_Attrib 0x0013 253 253 010 Pre-fail Always - 717297287648
173 Wear_Leveling_Count 0x0032 193 193 100 Old_age Always - 21488730204
174 Host_Reads_MiB 0x0022 099 099 000 Old_age Always - 6493129
175 Host_Writes_MiB 0x0022 099 099 000 Old_age Always - 4531334
192 Power-Off_Retract_Count 0x0012 099 099 000 Old_age Always - 21
194 Temperature_Celsius 0x0022 047 028 000 Old_age Always - 53 (Min/Max 16/72)
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x001a 200 199 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum.
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
255 0 65535 Read_scanning was never started
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.